contact download


Catalog
Download

DP air leak tester that switches between two circuits for test pressure

LS-R910

Air Leak Testers
Helium/Hydrogen
Leak Testers
Pressure
Flow
Peripherals
Others
Sound/Vibration
Analyzer
Cosmo Super Gel

Two different types of pressure ranges can be tested using just one tester!

The newly available LS-R910 has touch panel operation, quality control with USB, multilingual support, etc. continuing with the convenience and easy of use of the LS-R900, and allowing for the testing of two different types of pressure ranges with just one tester.

The LS-R910 is a new leak tester that meets a variety of demands

Edge & Function

For tests where different ranges of test pressure are used with a single product

Test 1 location Test pressure 2 ranges

(Attention) Keep in mind that you cannot run test 1 and 2 simultaneously.

For example, this kind of product

For tests where 2 different ranges of test pressure are used for multiple test locations in a single product(A valve is needed for switching to a separate testing location.)

Test 3 locations Test pressure 2 ranges

(Attention) Keep in mind that you cannot run test 1 and 2 simultaneously.

For example, this kind of product

You can switch between two different types of test pressure ranges.

The combination of test pressure ranges of 2 circuits (Port-A/Port-B) can be chosen from the support table below.
Of the combinations of various pressure ranges, choose two types that meet your demands from the table below.　

Fine tuning of the test pressure is now simple.

Pressure is applied to the workpiece.
If you push the button above, it will be shifted to the following button for easy fine tuning of the pressure.

Pressure can be easily fine tuned without applying pressure to the workpiece.

During setup, a large numeric keypad appears, and all types of settings can be adjusted using the simple screen display.

Regarding the convenient functions of the LS-R900 which are included in the LS-R910, please consult the LS-R900 page.
Link --> LS-R900 product information


Spec

DP sensor and display (standard) Resolving power
Display range
Sensor range
Excess pressure on sensors
Display precision *1		 0.1 Pa
±2500 Pa
±1000 Pa
±2000 Pa
5 MPa
±2.5% of rdg ±1Pa、However 50Pa following ± 2Pa
Test Pressure Sensor and Display Display precision ±1% of F.S. ±1 digit (linearity, hysteresis, reproducibility)
Temperature properties ±0.1% of F.S. / °C
Display units *2 Test Pressure: kPa, MPa (PSI, kg/cm2, bar, mbar, mmHg, cmHg, inHg)
Leak volume Pa, kPa, mL/s, mL/min, L/min, Pa・m3/s, E-3 Pa・m3/s, Pa/s, Pa/min,
(mmH2O, inH2O, mmHg, in3/min, in3/d, , ft3/h)
Leak volume display 3 to 5 digits (floating point), sample rate: 10/second
Leak limit (standard) ±999.9Pa or less
Number of Channels 32ch（0～31）
Timer setting range 999.9 seconds (resolving power: 0.1 second)
Power Source AC100 to 240V±10%, 50/60Hz, 80VAmax
Fuse (T2.5A 250V)
Dielectric strength and resistance AC1400V 10 sec, DC500V 50MΩ
Internal solenoid power supply:  DC24V
Test pressure source Uses clean air.The original pressure must be sufficiently higher than the test pressure.
Pilot pressure source Applies 400 to 700kPa of clean air.
CPU ARM9 400MHz, DRAM 128MB
LCD/TP 5.7 inch color LED 640 x 480 pixels (VGA)
Pipe connection diameter Rc(PT) 1/4 test pressure supply, pilot air supply, workpiece piping, master piping
Ambient temperature Operating temperature  5 to 45°C  Storage temperature:  -20 to 60°C
Consult if using in a high temperature environment.
Humidity 80 %RH or less  No dew condensation
Mass Approx. 14kg (standard specifications)
Serial communications RS232C-based
(D-sub9-pin)
2 port		 I/F fixed length output Leak data and set values are outputted simultaneously
ID/F fixed length output
Standard settings		 Leak data and set values are outputted simultaneously
T/F fixed length output Only leak data outputted
Other formats
USB Port Saving data Saves decisions, leak values, correction values, test pressure, WK#, CH#,  and time on inserted memory.
(Automatic file creation every 24 hours)
Set values storage All channel settings, system settings, etc.
LAN Port Intend to include FTP server function
Maintenance/calibration port M10 x 1.5 (O-ring seal)
Electro-pneumatic regulator Repeatability:  ±0.5% of F.S. and belowTemperature properties:  ±0.16% of F.S./°C
Control I/O connector, caps (2) for RS-232C, USB cover, test report, traceability documents, user manual
Ambient properties (IEC 6101-1) Overvoltage category II Protection class I
Peripherals Master chamber, leak master, bypass unit, external exhaust valve, etc.

*1 The display precision is that at the time of delivery.
The precision when inspecting and calibrating is ± 5% of rdg ±1Pa.
The precision of the DP display of the option, wide range is ± 5% of rdg ±0.01kPa.
*2 The unit ( ) is not fixed in the SI unit specifications.
NOTE: 　 If using overseas, please use a power cord that conforms to the respective country’s norms and regulations.

Classification

You can switch between two different types of test pressure ranges.

pic_ls-r910_8e

■　Model　LS-R910 – ①②③④⑤

① Pneumatic Circuit A1：Intelligent 1 Pneumatic Circuit,　A2：Intelligent 2 Pneumatic Circuit,
AS1：Intelligent 1 Pneumatic Circuit for small-volume workpieces.　AS01：Micro-volume workpiece circuit,    C：External pressure detection type
② Pressure range
（Port-A)		 Electro-pneumatic regulator LR：10～95kPa、MR：50～800kPa、VR：-5～-75kPa
Regulator L02：5～20kPa、　L：10～100kPa、　M：50～800kPa、

H20：2.0MPa以下 *1、　H49：4.9MPa以下 *1
③ Pressure range
（Port-B)		 Electro-pneumatic regulator LR：10～95kPa、MR：50～800kPa、VR：-5～-75kPa
Regulator L02：5～20kPa、　L：10～100kPa、　M：50～800kPa、V：-5～-100kPa
④ Options J：Leak Master support,　K05：ALC-05付0.5mL、　K1：ALC-1付1mL、
K4：ALC-4付4mL、　K10：ALC-10付10mL、
B：Bypass support (without regulator) *2、 B1：Bypass support (with regulator) *2、
D：DP sensor range ±10kPa
⑤ Power cable VA：AC125V 3m accessory cable,、　VE：AC250V 2m accessory cable

*1： A regulator is not included with H20, H49.

*2： B、B1   only support Port-B.



Appearance